How to remove plastic nut from toilet tank

thanks for support how can thank..

How to remove plastic nut from toilet tank

Renovation plans that call for new bathroom flooring or a toilet fixture require removal of the old toilet. When the old toilet doesn't come off smoothly, you may find that the anchor bolts, also referred to as closet bolts or flange bolts, are stripped when you try to remove the nuts. This common problem takes a little work to get the nuts and old bolts out.

Using various methods to remove the nuts and the bolts when the toilet bolt won't tighten gets your project back on track.

The division 1 weekly vendor reset

Turn the water supply shutoff valve clockwise to turn off the water supply to the toilet. This valve is located beneath the tank near the wall. Press and hold the lever to flush the toilet and remove as much water as possible. Soak up water remaining in the tank with a towel. Slide the tip of a screwdriver beneath the edge of one of the plastic caps covering the bolts on the base of the toilet and pop off the cap.

Remove the other cap in the same manner. Try turning the nut on the anchor bolts counterclockwise with a wrench. Insert a screwdriver through the hole in the bowl of the toilet and push the bolt to the side.

Windows update error 80092004 kb4519976

Turn the wrench counterclockwise while holding the bolt sideways to remove the nut. Slide the nut over the stripped threads and grasp the bolt beneath the nut with a pair of pliers if the threads are only stripped lower on the bolt. Turn the nut counterclockwise with a wrench to remove it. Repeat to remove the other nut. Grasp the top of the bolt with a pair of pliers if you still can't get the nuts off. Slide the blade on a hacksaw under the nut and cut the bolt. Repeat to cut the other bolt is you're unable to remove the other nut.

Grab both sides of the toilet bowl and rock the toilet from side to side to break the seal. Lift the toilet up to remove it. Remove remnants of the wax seal on the base of the toilet with a putty knife if you're reinstalling the same toilet. Remove the old wax seal on the floor with a putty knife.

Slide the stripped anchor bolts out of the flange in the floor. Push new anchor bolts through the holes in the flange where you removed the old bolts. Position a new wax seal over the flange and anchor bolts, making sure it's centered over the flange.

Lift the toilet up to position the base over the anchor bolts, and slide the toilet down onto the wax seal. Push down on the bowl to press the toilet into the seal. Place the nuts on the anchor bolts and turn them clockwise by hand to tighten. Sit on the bowl and tighten the nuts with a wrench. Don't over-tighten the nuts. Cut off the tops of the bolts with a hacksaw, so the plastic covers fit over the bolts.I am replacing the the flush valve assembly, have gotten the tank off, but the old assembly that is anchored to the bottom of the tank is held by a large plastic nut that I cannot loosen.

I've been working on it for 45 minutes. Is there a tool that I can get? I've drenched it in WD40, and have to stop for a bit. Will that do it if I wait long enough? If you wait a little while longer the WD40 should loosed it but there's other good lubricate sprays at Canadian Tire's that are effective to use.

A portable. Twist it and use it to the two hook the pen or dislodge it so it falls down into the optimum drain. Your expenditures for all of that at the same time are below the plumber's minimum charge. If you have a large screw driver and hammer, place the tip of the screw driver on the plastic nut at an angle and hit the handle end with your hammer, With a couple whacks you should be able to get your nut off.

As a last resort use a hammer and wood chisel or screwdriver. Trending News. CDC adds new signs to list of virus symptoms. FDA warns of dozens more hand sanitizers to avoid.

Photo of Ted Cruz on a plane with no mask goes viral. Inside Lisa Marie Presley's close bond with late son, Will trademarking possible D.

how to remove plastic nut from toilet tank

Black residents oppose Trump's visit to Jacksonville. All eyes are on Disney World following its reopening. Biden unveils plan to create 1 million jobs. Naya Rivera's selfless last act: Saving her son's life. Answer Save. A portable Dremel kit with carbide blade should be able to cut the plastic nut off within seconds. How do you think about the answers? You can sign in to vote the answer. Nope WD is for metal. Now you just made it slippery.

Plumbers tool - A large wrench.

Ge dishwasher 665

Still have questions? Get your answers by asking now.Questions and discussions about toilets, sinks, faucets, drainage, venting, water heating, showers, pumps, water quality, and other exclusively PLUMBING related issues. Please refrain from asking where to purchase a product, or business, pricing, or legal questions, or for contractor referrals, or any questions not related to plumbing.

Keep all posts positive and absolutely no advertising. This site is free, ad free, pop-up free and made possible by:.

I'm installing a new flush valve system in my toilet And I'm having trouble with one part. What do i use, and how do i remove the Big Mounting Nut at the bottom of the tank? I know it might sound simple, but this is my first time lol and I don't want to mess anything up on it and accidentally crack the toilet.

Please help! Thank you in advance. I just use a channel locks. I'm not sure how mechanically inclined you are, but just make sure that if you are on your back or side and you are looking up at it, make sure you are turning it counter clockwise. How old is the toilet? What kind is it? Is the shaft plastic or metal? I know this is common sense for most, but not for all. Also, make sure you have lots of rags and soak up the inside of the toilet. If there is still water in the bottom of the tank and you loosen that nut, water will start to come out.

Hope this helps. I've already taken the tank off. I just need to remove the mounting nut off so i can replace everything in the toilet. And its plastic. The toilet is about 4 years old. Pair of large Channelock pliers, but that is one piece that almost never has to be replaced. In fact, if it is that new, I am wondering if you had to do any of the major things you seem to have started.I have a duplex apartment which has 30 year old plumbing, all galvanized. My problem is that I have a bathtub in which the handles and spout are leaking, mostly hot water.

I have been able to remove the handles with a handle puller. My problem is that I cannot get the packing nuts off. They are I shut off the main water supply as I am attempting to replace my toilet tank. When I Looked underneath the toilet, both wing nuts are rusted, and broken off.

I sprayed WD To try to loosen without any luck. Any ideas please. Hi, this is Peter I have a Craftman lawn mover won't start. I found out that is the intake valve stuck close I took of the intake and cleaned it. It fire up but then after 3 minutes it shut off and stuck again.

I try to clean the valve and valve guide up to 3 times and it done same thing over How I remove a broken plastic toilet flange. Do I need to call a plumber to fix a leaking intake valve for cold water to my washing machine -- is this a soldering job? The valve leaks when I open it, and drips even when I shut it closed clockwise.

Thanks, I tried searching this page and didn't see any previous posts, sorry if I am repeating Remember Me? Find questions to answer Find today's questions Find unanswered questions. Search Topics. Login Not a member? Join our community. Sep 21,PM. Removing stuck plastic nuts holding toilet valve to the intake tube.

How do I loosen a nut at the bottom of the toilet tank?

I am trying to replace the valves inside the toilet tank. I have done this before and always seem to have a problem.Your toilet has two hoses. One is attached to the fill valve and directs water into the tank, while the other connects the fill valve to the water supply.

The first hose isn't under pressure, and you can simply push it onto the fill valve outlet, but the other is attached with a watertight connector. Many contemporary supply hoses are made of flexible plastic, but older ones are chrome or bendable rigid metal.

Hoses with plastic connectors are removable by hand, but you'll probably need pliers to unscrew a metal connector, especially if it's corroded. Turn off the water valve and drain the toilet tank before removing the hose from the tank. The best way to drain the tank is to hold down the flush handle for about 10 seconds. Locate the supply hose connector under the tank and note whether it's made of plastic or metal.

If it's plastic, you'll probably be able to unscrew it by hand. Put a bucket under the tank before you do, because a small amount of water will drain when the nut is removed. Unscrew a metal connector with a wrench or adjustable pliers.

If the nut is corroded, the fill valve may turn when you turn the nut. If so, hold the top of the fill valve with one hand while you turn the nut with the other. Spray lubricant on the nut to loosen it if you're having trouble getting it to turn. Give the lubricant about five minutes to work before trying again. Unscrew the other end of the hose from the shut-off valve once you've removed one end from the toilet. The connector on that end is almost always metal, so you'll need a wrench or pliers to unscrew it.

Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since As a landscape builder, he helped establish two gardening companies.

By Chris Deziel. Things Needed. Photo Credits. About the Author.The fill valve is the mechanism inside the water tank of the toilet that refills it to the right height after the toilet is flushed. Replacement fill valves can be bought at any hardware store, and any fill valve will do in terms of which one to buy, they are usually adjustable.

how to remove plastic nut from toilet tank

Here are the steps to removing your old fill valve and installing a new one. The fill valve is in the water tank, so your first step will be to remove the lid on top of your toilet's tank.

Be careful, as it might be heavy, and water may have condensed onto the roof of the lid. Now, you need to shut off the water supply line that feeds water into the tank. You can do this by turning the shutoff valve at the end of the line clockwise. After you shut the water off, you should flush the toilet and hold the handle down to drain as much water out of the tank as possible.

How to Remove the Coupling Nut on a Toilet

After the water has been shut off, you can unscrew the water supply line from the bottom of the fill valve. I recommend placing a bucket or some sort of container underneath the area where you are working, as some water will come out of the supply line when you un-screw it. After the water supply line has been dis-connected, you can un-screw the white plastic nut that hold the fill valve in place. You might be able to just do it by hand, but if you find it to be too difficult, I recommend using an adjustable crescent wrench, a channellock, or a pipe wrench.

If you do need to use a tool, be careful not to strip the nut, make sure to find a tool that can grip it appropriately. Make sure you have a container underneath the hole that the fill valve was in, because when you pull the fill valve out any water remaining inside the tank will flow out of the hole.

The old fill valve will probably still be wet, so you can drop that in the container that you have underneath.

After the old fill valve is out, you can grab your new fill valve and place it inside the tank where the old fill valve used to be. When you buy a new fill valve, it should come with a new nut to use underneath the tank to hold it in place. Put that nut over the end of the fill valve underneath the tank just like the old fill valve, and screw it into place.

how to remove plastic nut from toilet tank

You don't need to screw it in too tight, and if you are using a tool be careful how tight you screw it in. If the new fill valve didn't come with a new nut, the one from the old fill valve will work.

After the new fill valve is in place, you can hook the new refill tube onto the overflow tube. After you turn the water back on, water should start to flow into the tank, and the tank should begin to fill up. The fill valve controls at what level the tank stops filling up, and the height at which the tank stops filling up is adjustable. Right after you install the new fill valve, you may have to adjust it and go by trial and error until you get the water to stop at the desired place.

By aangus Follow. More by the author:. Participated in the Makerspace Contest View Contest. Did you make this project? Share it with us!

How to Remove a Toilet Seat With Stuck Nuts

I Made It! Disco Ball Hanging Planter by audreyobscura in Gardening. Concrete Class 18, Enrolled. Reply Upvote.To remove the entire toilet or just replace the water fill valve or ballcock, you always need to remove the coupling nut.

This nut basically secures the water supply line to the toilet. It's typically located underneath the tank, on the outside, where the water comes in. It's not difficult to remove the coupling nut, but there are steps you must first take before you even touch a wrench to it.

Otherwise, you'll have a mess to clean up. Shut the water off. Locate the water shutoff valve behind the toilet. Turn it clockwise until it won't turn any further. Flush the toilet and hold the handle down to completely empty the tank. Lift the toilet tank lid up and off carefully; set it aside so it doesn't get chipped or broken. Use a sponge to remove any water remaining in the tank.

Wring the sponge out in a bucket when it gets saturated.

Removing a Plastic Nut From a Toilet Seat Hinge

Locate the coupling nut on the underside of the toilet tank. Empty the bucket and place it underneath the water supply line. Use a pair of pliers to just loosen the coupling nut. Then finish loosening the nut with your fingers. Gently pull the nut down. The end of the water supply line will come away from the connection.

Place it in the bucket to drain the water inside it.

Frozen boost intercooler review

You're now ready to proceed with the rest of the steps needed for your replacement task. The coupling nut may be plastic. Use care when handling plastic plumbing parts.

how to remove plastic nut from toilet tank

They can easily be stripped, cracked or broken. When you replace the coupling nut, make sure not to over-tighten it. Kayar Sprang. Kayar Sprang has been a professional freelance writer and researcher since Sprang specializes in subjects she has expertise in, including gardening and home improvement.

She lives on and maintains a multi-acre farm.


Faem

thoughts on “How to remove plastic nut from toilet tank

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top